CLG-2086 Industrial Water Chloride ION Concentration Meter

CLG-2086 Industrial Chloride Concentration Meter
CLG-2086 chloride concentration is a high intelligent online continuous monitoring instrument, including the sensor and the secondary meter of two parts. It can be widely monitoring lakes water, surface water, water plant, sewage treatment plant, enterprises discharge waste water in water continuous monitoring. Random offers a variety of commonly used ion mode such as: H+, Ag+, Na+, K+, NH4+, cl-, F-, NO3-, BF4-, CN-, Cu2+, Pb2+, and support for user-defined ion mode, measurement of other ions.

Features
Computer-based: Multi-parameter measurement, temperature compensation and automatic range conversion
are achieved thanks to the high-performance CPU chip, high-precision AD conversion technology and SMT
pasting technology, resulting in high precision and repeatability.
High reliability: Single-board structure, touch keys, no switch knob or potentiometer. Rapid response,
accurate;
Water proof and dust-proof design: Its protection grade is IP54. It is applicable for outdoor use.
Electromagnetic compatibility (EMC/RFI) design: according to European standard EN50081 /50082
fabrication.
Alarm: Isolated alarm signal output, discretionary setting of upper and lower thresholds for alarming, and
lagged cancellation of alarming.
History curve: It can continuously record data for a month, with a point for each five minutes.
Notepad function: Recording 200 messages.
Instrument not crash: Watchdog procedures to ensure that the instrument will not working continuously crash
Offline measurement: Instead of laboratory sodium meter, performance can mark fluid examination  
instrument. The use of low cost, small amount of maintenance.

Technical Indexes
1. Measuring range:  chlorine concentration value: 0 ~ 5000 mg/L,     division value: 0.01mg/L;                                                     
                               temperature: 0～99.9℃;         division value: 0.01℃
                             potential value: - 1999 ~ +1999mV,  division value: 0.1mV;
2. Resolution: chlorine concentration value:±2.5% , temperature:± 0.5 ℃
3. Automatic temperature compensation range:: 0～99.9℃,with 25℃ as the reference temperature

4. Accuracy:±2.5%,±0.3℃
5. Water sample tested:: 0～99.9℃, 0.6MPa
6.Automatic temperature compensation error of the electronic unit: ±1.5%
7.Repeatability error of the electronic unit: ±0.02pH
8. Stability:±1.5%/24h
9. Clock accuracy: ±1 minute/month
10. Isolated current output: 4-20mA (load resistance <750Ω)
11. Output current error: ≤±l％FS
12. Data storage capacity: l month (1 point/5 minutes)
13. High and low alarm relay: AC220V, 7A

14. Communication interface: RS485(optional)
15.Power supply: AC220V±22V, 50Hz±1Hz,24VDC(optional)
16. Protection grade: lP65
17. Overall dimension: 146 (length) x 146 (width) x 108 (depth) mm;
dimension of the hole: 138 x 138mm
18. Weight: 1.0 kg
19. Working conditions: ambient temperature: 0-60℃; relative humidity: <85％

评论

发表评论

此博客中的热门博文

SJG-2083C INDUCTIVE ACID ALKALI CONCENTRATION METER

图片
SJG-2083C   INDUCTIVE ACID ALKALI CONCENTRATION METER SJG-2083C is inductive type acid alkali concentration meter,it's with inductive conductivity sensor,the measuring principle of the infinite sensor is a pair of wirewound alloy toroidal coils. The probe of the sensor is completely isolated from the measured process solution (non-contact). Two coils, one for transmitter and the other for receiver. When the transmitter coil is energized, the electrolyte solution conducts electricity and generates an induced current, which is directly proportional to the conductivity of the solution. The receiver coil detects the magnitude of this current and thus obtains the conductivity value of the solution. Conductivity probe alloy toroidal coil is customized in the toroidal molding with corrosion resistance. Because the probe of the sensor is completely isolated (non-contact) from the process under test (liquid), frequent maintenance and maintenance are not required.
阅读全文

CODS-3000-1 DIGITAL RS485 COD SENSOR

图片
CODS-3000-1  DIGITAL RS485 COD SENSOR Measuring Principle     The BOQU Digital Online COD Sensor is based on the absorption of ultraviolet light by organic matter, and uses the 254 nm spectral absorption coefficient SAC254 to reflect the important measurement parameters of soluble organic matter content in water, and can be converted into COD value under certain conditions. This method allows for continuous monitoring without the need for any reagents. Application 1)Continuous monitoring of organic matter load in the sewage treatment process 2)0n-line real-time monitoring of  influent and outflow water of the wastewater treatment 3)Application:surface water, industrial discharge water, and fishery discharge water etc
阅读全文

AH-800 Online Water Hardness and Alkali Analyzer

图片
Online W ater H ardness /Alkali   A nalyzer Model:AH-800 Online Water hardness and Alkali analyzer monits water total hardness or carbonate hardness and   total alkali  fully automatically via titration. Description Th is   analyzer  can measure water total hardness or carbonate hardness  and total alkali fully automaticlly via titration. This instrument is suitable for recognising levels of hardness, quality control of water softening facilities and monitoring of water blending facilities. The instrument allows two different limit values to be defined and checks the water quality by determining the absorbtion of the sample during titration of the reagent. The configuration of the many applications is supported by a configuration assistant. Features ◇ Reliable, exact and fully automatic analysing ◇ Simple commissioning with configuration assistant ◇ Self calibrating and self monitoring ◇ High measuring accuracy ◇ Easy maintenance and cleaning. ◇ Minimal reagent
阅读全文